List of the Best Brushless Motor Speed Controller in 2022

Comes Pre-soldered with XT60 Connector and 3.5mm bullet plugs

5v/3A UBEC (Very Efficient) - ESC can power receiver and servos

LiPo 2 - 4s (Cells), NiCd/NiMH: 5 - 12 Cells, 6.4V - 16.8V

Low Battery Protection, Overheat Protection, Startup Throttle Protection, Signal Loss Protection, and Abnormal Voltage Protection

Programmable - Programming Card or using Transmitter

Comes Pre-soldered with XT60 Connector and 3.5mm bullet plugs

5.5v/4A UBEC (Very Efficient)- ESC can power receiver and servos

LiPo 2 - 4s (Cells), NiCd/NiMH: 5 - 12 Cells, 6.4v - 16.8v

Low Battery Protection, Overheat Protection, Startup Throttle Protection, Signal Loss Protection, and Abnormal Voltage Protection

Programmable - Programming card or using Transmitter

Comes Pre-soldered with XT60 Connector and 3.5mm bullet plugs

5v/3A UBEC (Very Efficient) - ESC can power receiver and servos

LiPo 2 - 4s (Cells), NiCd/NiMH: 5 - 12 Cells, 6.4v - 16.8v

Low Battery Protection, Overheat Protection, Startup Throttle Protection, Signal Loss Protection, and Abnormal Voltage Protection

Programmable - Programming card or using Transmitter

2212 2200kv Brushless Motor

KV: 2200 RC plane kit

Motor Part Size : 27.5 x 38mm/ 1.08" x 1.8"(L*D)

30A Brushless ESC Input Voltage: 2-3 cells lithium battery or 6-9S NIMh battery

Suitable for RC Glider Quadcopter Helicopter Aircraft Copter Multi-copter

Durable-:The wires and interfaces for the controller and interfaces are durable,and ensure low malfunction of long time use.

Rigorous Design-:The controller shell is made of aluminium alloy with groove design,which can protect the inner circuit and good for heat dissipation to avoid thermal overloading.

Efficient-:This controller is a brushless motor controller,it can provide steady speed and sensitive control of braking and direction changes. Sine wave controller works smoothly and silently.

Wide Application-:The brush speed controller is suitable for electric bicycles, scooter,you can use it all of them.

Convenient to Install-:The interfaces have instruction labels on them for your easy installation.

【Wide Voltage】: Wide voltage input 7-70V, maximum output current 30A (Please refer to the recommended power range for actual use current. It is recommended that 12V within 250W, 24V within 350W, 48V within 450W, and 60V within 500W. )

【Speed Control Knob】: The knob has a switch function, which can control the motor speed from 0% to 100%. Adjustable potentiometer flexible cable can be separated, the cable length is 15CM.

【30A Fuse】: This set contains a 30A fuse to prevent shorting of the motor interface. Double protection of your Motor and Motor Speed Controller.

【Note 1】: The power of the input power supply must be greater than 1.5 times the rated power of the motor to make the motor work (note: the input voltage and the rated voltage of the motor must be consistent).

【Note 2】: If there is a forward-reverse circuit regulator on the children's car, please be sure to connect the speed controller between the power supply and the forward -reverse circuit regulator of the children's car. Otherwise, the speed controller may be damaged.

48V-72V 2000W Electric Bicycle Brushless Motor Controller for Scooter E-Bike.

For electric bicycle & scooter Mechanical or electric forklift etc.

48V/72VRated Voltage, 2000 Watts Rated Power.

Dimension: 21.5 * 8 * 4 cm (8.5 * 3.1 * 1.6 Inch).

The product according to market demand to do without Hall zero start, brushless dual-mode smart measure battery voltage, motor phase.

With micro single-chip system, this speed control can achieve simple system programming, which can suit better high-speed high-power brushless motors.

Safety Startup: To avoid any injury, the motor will not start up immediately if the potentiometer of speed controller is not at the lowest gear, which is necessary for high-speed high-power motor to protect user's safety.

Temperature Protection: The speed control has aluminum heat sink, which allows it work at 30 A continuously. When temperature reaches 110 celsius degree, temperature detect system will send a protection signal and system will auto decrease 60% power output to protect speed control and motor. It will back to normal power after temperature is decreased. To protect the actuator module, please dissipate heat during long-time using.

The signal loss prevention: Auto shut down when there is no signal detected from PWM signal generator(potentiometer ).

Power Identification System: The speed control has power identification system, which is designed for high-speed high-power motors such as in model plane. It is not suitable for low-power brushless motors.

★Application--It suitable for electric bicycles, scooter, etc.

★Premium Material--It made of aluminium alloy, this brushless controller is sturdy and durable.

★Sensitive Control--This item is a brushless motor controller, it can provide steady speed and sensitive control of braking and direction changes.

★High Performance--The wires and interfaces are durable, and ensure low malfunction of long time use.

★Easy to Use-- The interfaces have instruction labels on them for your easy installation.

1.Humanized design,the interface adopts binding posts,standard heat sink,integrated speed regulating potentiometer on the board,it can be used when the power is on,save time and effort.

2.Full patch technology,stable performance,with forward and reverse, brake function.Electric Motor Speed Controller Brushless Controller with Hall.

3.Wide voltage 6-60V high power 400W DC three-phase brushless with Hall controller.

4.Support PLC 0-5V analog quantity control, support PWM to 0-5V control.

5.There are three relatively thick phase wires on the motor, and there are also three phase wire interfaces on the driver board. They are marked with the characters of MA, MB, MC and other similar characters, and they are also connected respectively.